Skip to main content

PyTorch Code for Simple Neural Networks for MNIST Dataset

LEACH protocol installation in ns2 (ns-2.35)

This post shows you the method to install the LEACH protocol developed by MIT called MIT-uAMPS which was developed in the year 2000. So you may face some problem in installing this protocol in recent Operating Systems.

I have tried to compile this protocol in ns-2.35 which was running under Ubuntu 14.04 64 bit OS
Here is the requirement before you proceed to install.
Assumptions:
Assuming that you have successfully installed ns-2.35 before you start compiling LEACH. If you need any help in installing ns2, refer this post. http://www.nsnam.com/2014/11/ns2-installation-in-ubuntu-1404.html

  • Install gcc-4.4 and g++-4.4 for compiling this LEACH (but the recommended is gcc-4.3 but it is not there in the synaptic package manager)
  • To install the above, first you tries these packages
sudo apt-get update 
sudo apt-get install build-essential autoconf automake libxmu-dev gcc-4.4 g++-4.4

Please see the video for more instructions 




Installation of LEACH in ns-2.35 

From the downloaded files , copy both the leach-setup.sh and the ns-leach-2.35.tar.gz in the same folder. Open the terminal and run as shown below.

$] sh leach-setup.sh
After the above step, all files will be unzipped and copied to their locations and now an 

Important Step

The following four files contains some path information about other files, these path information have to be updated in these files. Also these four files are located at two different locations. 
Location1: /home/pradeepkumar/ns-allinone-2.35/ns-2.35/mit/uAMPS/ 
Location2: /home/pradeepkumar/ns-allinone-2.35/ns-2.35/tcl/mobility/ 
Change the paths as mentioned in the video and replace the files at both the location with the updated path information.  
leach.tcl
leach-c.tcl
mte.tcl
stat-clus.tcl 

To test LEACH Protocol

To test leach protocol, go to this folder
$] cd ns-allinone-2.35/ns-2.35/
$] ./leach_test

once done, go to the folder
$] cd mit/leach_sims/
LEACH
Leach Protocol

open the files leach.out or anything with the name leach.* (these data are relevant to LEACH), if you want to run leach-c, change the line alg=leach-c in the file leach_test  

Thats it!!!!! 

I have given the elaborate information on LEACH, for any doubts, refer http://www.nsnam.com,

Please comment below, if you got any further inputs or updates. 
Thanks to http://anupamasikchi.blogspot.in/ (for information related to LEACH, all the particulars given in this link is reflected in my code).

T S Pradeep Kumar

Comments

  1. sir I have found a problem during running of leach "./leach_test: line 37: ns: command not found"

    ReplyDelete
    Replies
    1. You need to watch the video carefully and set the environment variables
      PATH
      LD_LIBRARY_PATH
      TCL_LIBRARY

      Delete
  2. hi how to create nam file for leach protocol

    ReplyDelete
  3. Sir, I am unable to install gcc-4.4
    It says, Package gcc-4.4 is not available, but is referred to by another package.
    This may mean that the package is missing, has been obsoleted, or
    is only available from another source

    Package g++-4.4 is not available, but is referred to by another package.
    This may mean that the package is missing, has been obsoleted, or
    is only available from another source


    So, what is the alternative for this
    ?

    ReplyDelete
  4. And now, I had to reinstall ns2. Thank you.

    ReplyDelete
  5. Hi sir, please how to create nam file for leach protocol

    ReplyDelete
  6. Hi sir, please how to create nam file for leach protocol

    ReplyDelete
  7. hello doctor, can you help me please where to find or any other idea about Energy Efficient Clustering Scheme(EECS)?

    ReplyDelete
  8. Sir, while installation of LEACH protocol, I was unable to copy paste the shell file and then I had to do that manually. After installation, the LEACH file showed some error but the LEACH-C file was running smoothly. I don't know what is going on.

    ReplyDelete
  9. Sir, Clear the given error
    make: *** No rule to make target 'mit/rca/rcagent.c', needed by 'mit/rca/rcagent.o'. Stop.
    Ns make failed!
    See http://www.isi.edu/nsnam/ns/ns-problems.html for problems

    ReplyDelete
    Replies
    1. Open ns-allinone-2.35/ns-2.35/Makfile.in. Replace the line $(OBJ_MIT:.o=.c) with $(OBJ_MIT:.o=.cc).

      Delete
    2. Open the file ns-allinone-2.35/ns-2.35/Makefile.in. Replace the line $(OBJ_MIT:.o=.c) with $(OBJ_MIT:.o=.cc).

      Delete

Post a Comment

Popular posts from this blog

Installing ns3 in Ubuntu 22.04 | Complete Instructions

In this post, we are going to see how to install ns-3.36.1 in Ubuntu 22.04. You can follow the video for complete details Tools used in this simulation: NS3 version ns-3.36.1  OS Used: Ubuntu 22.04 LTS Installation of NS3 (ns-3.36.1) There are some changes in the ns3 installation procedure and the dependencies. So open a terminal and issue the following commands Step 1:  Prerequisites $ sudo apt update In the following packages, all the required dependencies are taken care and you can install all these packages for the complete use of ns3. $ sudo apt install g++ python3 python3-dev pkg-config sqlite3 cmake python3-setuptools git qtbase5-dev qtchooser qt5-qmake qtbase5-dev-tools gir1.2-goocanvas-2.0 python3-gi python3-gi-cairo python3-pygraphviz gir1.2-gtk-3.0 ipython3 openmpi-bin openmpi-common openmpi-doc libopenmpi-dev autoconf cvs bzr unrar gsl-bin libgsl-dev libgslcblas0 wireshark tcpdump sqlite sqlite3 libsqlite3-dev  libxml2 libxml2-dev libc6-dev libc6-dev-i386 libclang-dev llvm-

Installation of NS2 (ns-2.35) in Ubuntu 20.04

Installation of NS2 (ns-2.35) in Ubuntu 20.04 LTS Step 1: Install the basic libraries like      $] sudo apt install build-essential autoconf automake libxmu-dev Step 2: install gcc-4.8 and g++-4.8 open the file using sudo mode $] sudo nano /etc/apt/sources.list Include the following line deb http://in.archive.ubuntu.com/ubuntu bionic main universe $] sudo apt update $] sudo apt install gcc-4.8 g++-4.8 Step 3:  Unzip the ns2 packages to home folder $] tar zxvf ns-allinone-2.35.tar.gz $] cd ns-allinone-2.35/ns-2.35 Modify the following make files. ~ns-2.35/Makefile.in Change @CC@ to gcc-4.8 change @CXX@ to g++-4.8 ~nam-1.15/Makefile.in ~xgraph-12.2/Makefile.in ~otcl-1.14/Makefile.in Change in all places  @CC@ to gcc-4.8 @CPP@ or @CXX@ to g++-4.8 open the file: ~ns-2.35/linkstate/ls.h Change at the Line no 137  void eraseAll() { erase(baseMap::begin(), baseMap::end()); } to This void eraseAll() { this->erase(baseMap::begin(), baseMap::end()); } All changes made Step 4: Open a new termi

Installation of NS2 in Ubuntu 22.04 | NS2 Tutorial 2

NS-2.35 installation in Ubuntu 22.04 This post shows how to install ns-2.35 in Ubuntu 22.04 Operating System Since ns-2.35 is too old, it needs the following packages gcc-4.8 g++-4.8 gawk and some more libraries Follow the video for more instructions So, here are the steps to install this software: To download and extract the ns2 software Download the software from the following link http://sourceforge.net/projects/nsnam/files/allinone/ns-allinone-2.35/ns-allinone-2.35.tar.gz/download Extract it to home folder and in my case its /home/pradeepkumar (I recommend to install it under your home folder) $ tar zxvf ns-allinone-2.35.tar.gz or Right click over the file and click extract here and select the home folder. $ sudo apt update $ sudo apt install build-essential autoconf automake libxmu-dev gawk To install gcc-4.8 and g++-4.8 $ sudo gedit /etc/apt/sources.list make an entry in the above file deb http://in.archive.ubuntu.com/ubuntu/ bionic main universe $ sudo apt update Since, it&#