Skip to main content

Wireless Node Configuration in Network Simulator 2 (NS2)

The node configuration in ns2 is a special task in which the number of nodes can be configured for a set of parameters. The following table tells about the node  configuration parameters as defined in the ns-lib.tcl

The readers are requested to refer the ns-lib.tcl file for more information.

Option Available Values Remarks
addressType flat, hierarchichal  
MPLS ON,OFF Multi protocol Label Switching
wiredRouting ON, OFF  
llType LL, LL/Sat Link Layer
macType Mac/802_11, Mac/Csma/Ca, Mac/Sat, Mac/Sat/UnslottedAloha, Mac/Tdma Medium Access Control
ifqType Queue/DropTail, Queue/DropTail/PriQueue Interface Queue type
phyType Phy/wirelessPhy, Phy/Sat Physical Layer Type
adhocRouting DIFFUSION/RATE, DIFFUSION/PROB, DSDV, DSR, FLOODING, OMNIMCAST,AODV,TORA,PUMA adhoc routing protocol
propType Propagation/TwoRayGround, Propagation/Shadowing Propagation Type
antType Antenna/OmniAntenna, Antenna type
Channel Channel/WirelessChannel, Channel/Sat Channel to be used
mobileIP ON,OFF to set the IP for Mobile or not
energyModel EnergyModel energy model to be enabled or not
initialEnergy <joule> in terms of joules (Ex: 3.24)
txPower   Power in terms of Watts (0.32)
rxPower   Power in terms of Watts (0.1)
idlePower   Power in terms of Watts (0.02)
agentTrace ON, OFF Tracing to be on or off
routerTrace ON, OFF Tracing to be on or off
macTrace ON, OFF Tracing to be on or off
movementTrace ON, OFF Tracing to be on or off
errProc UniformErrorProc  
toraDebug ON, OFF  

 

An Example

$ns node-config -addressType hierarchical \
                   -adhocRouting AODV \
                   -llType LL \
                   -macType Mac/802_11 \
                   -ifqType Queue/DropTail/PriQueue \
                   -ifqLen 50 \
                   -antType Antenna/OmniAntenna \
                   -propType Propagation/TwoRayGround \
                   -phyType Phy/WirelessPhy \
                   -topologyInstance \$topo \
                   -channel Channel/WirelessChannel \
                   -agentTrace ON \
                   -routerTrace ON \
                   -macTrace OFF \
                   -movementTrace OFF
Labels:

Comments

  1. UnknownNovember 8, 2012 at 7:27 PM

    Dear all , who can help me for design network , and node configuration , and how can select tx power and rxpower??whats level for tx power and rxpower??

    thanks

    ReplyDelete
    Replies
    1. AnonymousFebruary 23, 2013 at 8:10 PM

      dear i am also facing such problem...if u got then plz mail me on mohit.roorkee@gmail.com

      Delete
    2. T S Pradeep KumarFebruary 23, 2013 at 10:44 PM

      depending on the type of network, you can set the power. for WSN, you can get the power history of a IRIS or MICA and set the corresponding values, for a wifi network, set power based on the battery profile of the device.....

      Delete
  2. ShitalDecember 18, 2012 at 11:59 AM

    I am facing error,

    segmentation fault(core dumped)

    Please help me..

    ReplyDelete
    Replies
    1. UnknownJanuary 24, 2013 at 10:34 PM

      simply change energy value like if using 70 try for 90,100......

      Delete
  3. UnknownMarch 7, 2013 at 10:52 AM

    Hi all, Can you suggest me how to fill buffer(queue) of intermediate nodes in ns2 through tcl script. ??

    ReplyDelete

Post a Comment

Popular posts from this blog

How to Create Ubuntu 24.04 Bootable USB Using Rufus [Step-by-Step Guide]

How to Create Ubuntu 24.04 Bootable USB Using Rufus [Step-by-Step Guide] Are you planning to install or try Ubuntu 24.04 LTS ? The easiest and most reliable method is to create a bootable USB drive using Rufus on a Windows system. This detailed guide will help you create a Ubuntu 24.04 USB bootloader using Rufus with easy-to-follow steps and screenshots (optional). Here is the complete video of the bootloader creation and OS installation in Windows 11. 🧰 Requirements A USB flash drive (minimum 8GB recommended) A Windows PC Ubuntu 24.04 LTS ISO file Rufus USB creation tool 🧾 Steps to Create a Ubuntu 24.04 Bootable USB Using Rufus ✅ Step 1: Download Ubuntu 24.04 ISO Visit the official Ubuntu website and download the Ubuntu 24.04 LTS ISO file . ✅ Step 2: Download and Run Rufus Head to Rufus official site and download the latest version. Open the executable file (no installation required). ✅ Step 3: Insert USB Drive Plug in your USB drive. Rufus ...
Post a Comment
Read more

Installing ns3 in Ubuntu 22.04 | Complete Instructions

In this post, we are going to see how to install ns-3.36.1 in Ubuntu 22.04. You can follow the video for complete details Tools used in this simulation: NS3 version ns-3.36.1  OS Used: Ubuntu 22.04 LTS Installation of NS3 (ns-3.36.1) There are some changes in the ns3 installation procedure and the dependencies. So open a terminal and issue the following commands Step 1:  Prerequisites $ sudo apt update In the following packages, all the required dependencies are taken care and you can install all these packages for the complete use of ns3. $ sudo apt install g++ python3 python3-dev pkg-config sqlite3 cmake python3-setuptools git qtbase5-dev qtchooser qt5-qmake qtbase5-dev-tools gir1.2-goocanvas-2.0 python3-gi python3-gi-cairo python3-pygraphviz gir1.2-gtk-3.0 ipython3 openmpi-bin openmpi-common openmpi-doc libopenmpi-dev autoconf cvs bzr unrar gsl-bin libgsl-dev libgslcblas0 wireshark tcpdump sqlite sqlite3 libsqlite3-dev  libxml2 libxml2-dev libc6-dev libc6-dev-i386 libc...
3 comments
Read more

NS2 (NS-2.35) Installation in Ubuntu 11.10

This post will help you in installing Network Simulator 2 version NS2.35 in Ubuntu 11.10 Instructions Install Ubuntu Download NS-2.35 ( http://sourceforge.net/projects/nsnam/files/allinone/ns-allinone-2.35/ns-allinone-2.35.tar.gz/download ) Unzip or untar it to any folder (recommended is /home/ loginname) using the following commands one by one sudo apt-get update sudo apt-get install build-essential autoconf automake libxmu-dev tar zxvf ns-allinone-2.35.tar.gz cd ns-allinone-2.35 ./install Once installed the PATH information will be provided to you. Copy the PATH and LD_LIBRARY_PATH Variable to .bashrc (see a dot in the beginning) Input the path information in .bashrc file like this export PATH=$PATH:<Place your paths here> export LD_LIBRARY_PATH=$LD_LIBRARY_PATH: <place the LD_LIBRARY_PATHS> here. Once done, save the file and close execute the command source .bashrc try ns or nam to see whether your installation succeeded.
77 comments
Read more