Skip to main content

PyTorch Code for Simple Neural Networks for MNIST Dataset

Wireless Node Configuration in Network Simulator 2 (NS2)

The node configuration in ns2 is a special task in which the number of nodes can be configured for a set of parameters. The following table tells about the node  configuration parameters as defined in the ns-lib.tcl

The readers are requested to refer the ns-lib.tcl file for more information.

Option Available Values Remarks
addressType flat, hierarchichal  
MPLS ON,OFF Multi protocol Label Switching
wiredRouting ON, OFF  
llType LL, LL/Sat Link Layer
macType Mac/802_11, Mac/Csma/Ca, Mac/Sat, Mac/Sat/UnslottedAloha, Mac/Tdma Medium Access Control
ifqType Queue/DropTail, Queue/DropTail/PriQueue Interface Queue type
phyType Phy/wirelessPhy, Phy/Sat Physical Layer Type
adhocRouting DIFFUSION/RATE, DIFFUSION/PROB, DSDV, DSR, FLOODING, OMNIMCAST,AODV,TORA,PUMA adhoc routing protocol
propType Propagation/TwoRayGround, Propagation/Shadowing Propagation Type
antType Antenna/OmniAntenna, Antenna type
Channel Channel/WirelessChannel, Channel/Sat Channel to be used
mobileIP ON,OFF to set the IP for Mobile or not
energyModel EnergyModel energy model to be enabled or not
initialEnergy <joule> in terms of joules (Ex: 3.24)
txPower   Power in terms of Watts (0.32)
rxPower   Power in terms of Watts (0.1)
idlePower   Power in terms of Watts (0.02)
agentTrace ON, OFF Tracing to be on or off
routerTrace ON, OFF Tracing to be on or off
macTrace ON, OFF Tracing to be on or off
movementTrace ON, OFF Tracing to be on or off
errProc UniformErrorProc  
toraDebug ON, OFF  

 

An Example

$ns node-config -addressType hierarchical \
-adhocRouting AODV \
-llType LL \
-macType Mac/802_11 \
-ifqType Queue/DropTail/PriQueue \
-ifqLen 50 \
-antType Antenna/OmniAntenna \
-propType Propagation/TwoRayGround \
-phyType Phy/WirelessPhy \
-topologyInstance \$topo \
-channel Channel/WirelessChannel \
-agentTrace ON \
-routerTrace ON \
-macTrace OFF \
-movementTrace OFF

Comments

  1. Dear all , who can help me for design network , and node configuration , and how can select tx power and rxpower??whats level for tx power and rxpower??

    thanks

    ReplyDelete
    Replies
    1. dear i am also facing such problem...if u got then plz mail me on mohit.roorkee@gmail.com

      Delete
    2. depending on the type of network, you can set the power. for WSN, you can get the power history of a IRIS or MICA and set the corresponding values, for a wifi network, set power based on the battery profile of the device.....

      Delete
  2. I am facing error,

    segmentation fault(core dumped)

    Please help me..

    ReplyDelete
    Replies
    1. simply change energy value like if using 70 try for 90,100......

      Delete
  3. Hi all, Can you suggest me how to fill buffer(queue) of intermediate nodes in ns2 through tcl script. ??

    ReplyDelete

Post a Comment

Popular posts from this blog

Installing ns3 in Ubuntu 22.04 | Complete Instructions

In this post, we are going to see how to install ns-3.36.1 in Ubuntu 22.04. You can follow the video for complete details Tools used in this simulation: NS3 version ns-3.36.1  OS Used: Ubuntu 22.04 LTS Installation of NS3 (ns-3.36.1) There are some changes in the ns3 installation procedure and the dependencies. So open a terminal and issue the following commands Step 1:  Prerequisites $ sudo apt update In the following packages, all the required dependencies are taken care and you can install all these packages for the complete use of ns3. $ sudo apt install g++ python3 python3-dev pkg-config sqlite3 cmake python3-setuptools git qtbase5-dev qtchooser qt5-qmake qtbase5-dev-tools gir1.2-goocanvas-2.0 python3-gi python3-gi-cairo python3-pygraphviz gir1.2-gtk-3.0 ipython3 openmpi-bin openmpi-common openmpi-doc libopenmpi-dev autoconf cvs bzr unrar gsl-bin libgsl-dev libgslcblas0 wireshark tcpdump sqlite sqlite3 libsqlite3-dev  libxml2 libxml2-dev libc6-dev libc6-dev-i386 libclang-dev llvm-

Installation of NS2 (ns-2.35) in Ubuntu 20.04

Installation of NS2 (ns-2.35) in Ubuntu 20.04 LTS Step 1: Install the basic libraries like      $] sudo apt install build-essential autoconf automake libxmu-dev Step 2: install gcc-4.8 and g++-4.8 open the file using sudo mode $] sudo nano /etc/apt/sources.list Include the following line deb http://in.archive.ubuntu.com/ubuntu bionic main universe $] sudo apt update $] sudo apt install gcc-4.8 g++-4.8 Step 3:  Unzip the ns2 packages to home folder $] tar zxvf ns-allinone-2.35.tar.gz $] cd ns-allinone-2.35/ns-2.35 Modify the following make files. ~ns-2.35/Makefile.in Change @CC@ to gcc-4.8 change @CXX@ to g++-4.8 ~nam-1.15/Makefile.in ~xgraph-12.2/Makefile.in ~otcl-1.14/Makefile.in Change in all places  @CC@ to gcc-4.8 @CPP@ or @CXX@ to g++-4.8 open the file: ~ns-2.35/linkstate/ls.h Change at the Line no 137  void eraseAll() { erase(baseMap::begin(), baseMap::end()); } to This void eraseAll() { this->erase(baseMap::begin(), baseMap::end()); } All changes made Step 4: Open a new termi

Installation of NS2 in Ubuntu 22.04 | NS2 Tutorial 2

NS-2.35 installation in Ubuntu 22.04 This post shows how to install ns-2.35 in Ubuntu 22.04 Operating System Since ns-2.35 is too old, it needs the following packages gcc-4.8 g++-4.8 gawk and some more libraries Follow the video for more instructions So, here are the steps to install this software: To download and extract the ns2 software Download the software from the following link http://sourceforge.net/projects/nsnam/files/allinone/ns-allinone-2.35/ns-allinone-2.35.tar.gz/download Extract it to home folder and in my case its /home/pradeepkumar (I recommend to install it under your home folder) $ tar zxvf ns-allinone-2.35.tar.gz or Right click over the file and click extract here and select the home folder. $ sudo apt update $ sudo apt install build-essential autoconf automake libxmu-dev gawk To install gcc-4.8 and g++-4.8 $ sudo gedit /etc/apt/sources.list make an entry in the above file deb http://in.archive.ubuntu.com/ubuntu/ bionic main universe $ sudo apt update Since, it&#