Skip to main content

TCL installation error

In case, if ns2 have to be recompiled based on a new addition of protocol or agent, there should be an entry to the Makefile.in. After the changes are made, the following things need to be done to compile the agents.

$] ./configure 
$] make 

but ./configure may throw an error as shown below like
"Configure: Error: Installation of Tcl Seems to be incomplete or not found"

tcl error
TCL Error
To correct this problem, please try the following

$] ./configure --with-tcl-ver=8.5 

The above works only after the successful installation of ns2. If you are installing ns2 for the first time refer this blog post

http://www.nsnam.com/2014/11/ns2-installation-in-ubuntu-1404.html



T S Pradeep Kumar

Popular posts from this blog

AWK Scripts for NS2 to process data from Trace Files

AWK Scripts are very good in processing the data from the log (trace files) which we get from NS2. If you want to process the trace file manually, here is the detailHere is a sample of trace file from NS2 (However ns2 supports a new type of trace file also), but this post will make you understand the old trace format only.r 0.030085562 _0_ MAC  --- 0 message 32 [0 ffffffff 1 800] ------- [1:255 -1:255 32 0] r 0.030110562 _0_ RTR  --- 0 message 32 [0 ffffffff 1 800] ------- [1:255 -1:255 32 0] s 1.119926192 _0_ RTR  --- 1 message 32 [0 0 0 0] ------- [0:255 -1:255 32 0]
AWK Scripts are very good in processing the data column wise. For example
the first column in the above trace file represents r, s which indicates receive, sent respectively. If we want to trace the entire r and s alone from this trace file we can represent it as $1
So
$1 represents ACTION
$2 Time
$3 Node ID
$4 Layer
$5 Flags
$6 seqno
$7 type
$8 Size
$14 Energy (if the network nodes includes EnergyModel)To run the awk script in Li…

nam installation - Segmentation Fault (Solved)

If you are encountering "Segmentation Fault" error while running nam in Ubuntu 14.04 or Linux Mint 17+ editions, this post will be helpful for you.

Download the nam file from this link

First, remove the nam which was installed earlier using the following command 

pradeep@localhost $] sudo apt-get remove nam

and install the new nam which was downloaded just now. go to the folder where the file was downloaded and issue the following command

pradeep@localhost $]  sudo dpkg --install nam_1.15-10_i386.deb

See the screenshot below to install and use nam

 T S Pradeep Kumar

Xgraph

Xgraph is an X-Windows application that includes: interactive plotting and graphing animation and deritives portability and bug fixes So to plot the characteristics of NS2 parameters like throughput, end to end delay, packets information, etc can be plotted using xgraph
The successful installation of NS2 will install xgraph also along with it.
To run xgraph from a shell prompt: # xgraph filename.xginside TCL scripts, xgraph can be written like this
exec xgraph filename.xg -geometry 500×500
if there are more xgraph files then,
exec xgraph filename1.xg -geometry 500×500 &
exec xgraph filename2.xg -geometry 500×500 &
The ambersand is mandatory to popup all the graph windows, if & (ambersand) is not there, then only the last xgraph window will be popped up.Sample xgraph file and its contents
/*** The xgraph file shows the information about the overhead with size of the network,
Overhead is compared with four routing protocols like AODV, DSR, D…